IEC 60061 7006-27b-1 Lamp Holder Gauge Go Gauge
IEC 60061 7006-27B-1 Lamp holder gauge go gauge
E27 Lamp holder gauge name
Meet the standard: IEC 60061; GB1483.1
Product category:
E27 Lamp holder gauge Pass Gauge 7006-27B-1
E27 Screw cap gauge Stop 7006-28A-1
E27 Lamp holder Solder Height Gauge 7006-27C-1
E27 Screw cap Contact performance Gauge 7006-50-1
E27 Lamp holder Anti-accidental contact gauge (anti-electric shock) 7006-51A-2
| Reference | Dimension(mm) | Tolerance(mm) | Limit after wear(mm) |
| d | 26.45 | +0.03/-0 | 26.50 |
| d1 | 24.26 | +0.03/-0 | 24.31 |
| L | 16.5 | ±0.1 | |
| O | 28 | ±0.2 | |
| P | 3.629 | – | |
| r | 1.025 | – | |
| T | 22.0 | +0.0/-0.03 | |
| V | 15 | ±0.1 | |
| W | 5 | ±0.1 |
The shape part of the edge of the thread shall be broken with radius of 0.2mm to 0.3mm.
IEC 60061 7006-27B-1 Lamp holder gauge go gauge
Purpose:
To check the maximum dimensions of the screw thread and dimension T1 minimum of caps on finished lamps.
IEC 60061 7006-27B-1 Lamp holder gauge go gauge
Testing
When the cap on a finished lamp has been screwed into the gauge as far as it will go, the center contact shall be co-planar with, or project beyond, surface X.
IEC 60061 7006-27B-1 Lamp holder gauge go gauge
E27 Lamp holder gauge name
Meet the standard: IEC 60061; GB1483.1
Product category:
E27 Lamp holder gauge Pass Gauge 7006-27B-1
E27 Screw cap gauge Stop 7006-28A-1
E27 Lamp holder Solder Height Gauge 7006-27C-1
E27 Screw cap Contact performance Gauge 7006-50-1
E27 Lamp holder Anti-accidental contact gauge (anti-electric shock) 7006-51A-2
| Reference | Dimension(mm) | Tolerance(mm) | Limit after wear(mm) |
| d | 26.45 | +0.03/-0 | 26.50 |
| d1 | 24.26 | +0.03/-0 | 24.31 |
| L | 16.5 | ±0.1 | |
| O | 28 | ±0.2 | |
| P | 3.629 | – | |
| r | 1.025 | – | |
| T | 22.0 | +0.0/-0.03 | |
| V | 15 | ±0.1 | |
| W | 5 | ±0.1 |
The shape part of the edge of the thread shall be broken with radius of 0.2mm to 0.3mm.
IEC 60061 7006-27B-1 Lamp holder gauge go gauge
Purpose:
To check the maximum dimensions of the screw thread and dimension T1 minimum of caps on finished lamps.
IEC 60061 7006-27B-1 Lamp holder gauge go gauge
Testing
When the cap on a finished lamp has been screwed into the gauge as far as it will go, the center contact shall be co-planar with, or project beyond, surface X.
所有评论仅代表网友意见，与本站立场无关。